Owing to its superior tribological and mechanical properties with corrosion resistance, biocompatibility, and hemocompatibility, diamond-like carbon (DLC) has emerged as a promising material for biomedical applications. DLC films with various atomic bond structures and compositions are finding places in orthopedic, cardiovascular, and dental applications. Cells grew on to DLC coating without any cytotoxity and inflammation. DLC coatings in orthopedic applications reduced wear, corrosion, and debris formation. DLC coating also reduced thrombogenicity by minimizing the platelet adhesion and activation. However, some contradictory results (Airoldi et al., Am J Cardiol 2004;93:474-477, Taeger et al., Mat-wiss u Werkstofftech 2003;34:1094-1100) were also reported that no significant improvement was observed in the performance of DLC-coated stainless stent or DLC-coated femoral head. This controversy should be discussed based on the detailed information of the coating such as atomic bond structure, composition, and/or electronic structure. In addition, instability of the DLC coating caused by its high level of residual stress and poor adhesion in aqueous environment should be carefully considered. Further in vitro and in vivo studies are thus required to confirm its use for medical devices.

/pdf/biomedical-applications-of-diamond-like-carbon-coatings-a-dkabt67isv.pdf

Biomedical applications of diamond-like carbon coatings : A review

Corrosion and surface modification on biocompatible metals: A review.

Surface reactions during growth and erosion of hydrocarbon films

The hemocompatibility of a TiN/TiC/diamond-like carbon (DLC) multilayer structure, deposited on titanium substrates for use as coatings for a heart valve prosthesis, has been studied through the adsorption of blood proteins and the adhesion and attachment of blood platelets. All of the surfaces were characterized by stylus profilometry and water contact angles. The adsorption of albumin and fibrinogen to the surfaces was assessed using the Amido Black assay, whereas platelet attachment was studied by scanning electron microscopy and quantified using stereological techniques. The degree of platelet spreading on the surfaces was seen to correlate with differences in surface energy, indicated from contact angle measurements. The greatest spreading was seen on the more hydrophilic surfaces. When studying protein adsorption to the surfaces, no correlation could be determined between contact angle results and levels of adsorption, although the most hydrophilic surfaces did appear to promote greater amounts of fibrinogen adsorption. Thrombus formation was observed to some degree on all of the surfaces, with the exception of the DLC coating. This coating also promoted less spreading of platelets than the other surfaces. The good hemocompatibility of the DLC coating is attributed to its hydrophobicity and smooth surface, resulting in a higher ratio of albumin to fibrinogen than any of the other surfaces.

Protein adsorption and platelet attachment and activation, on TiN, TiC, and DLC coatings on titanium for cardiovascular applications

Ti being bioinert shows poor bone cell adhesion with an intervening fibrous capsule. Ti could be made bioactive by several methods including growing in situ TiO2 layer on Ti-surface. TiO2 nanotubes were grown on Ti surface via anodization process and the bone cell-material interactions were evaluated. Human osteoblast cell attachment and growth behavior were studied using an osteoprecursor cell line for 3, 7, and 11 days. An abundant amount of extracellular matrix (ECM) between the neighboring cells was noticed on anodized nanotube surface with filopodia extensions coming out from cells to grasp the nanoporous surface of the nanotube for anchorage. To better understand and compare cell-materials interactions, anodized nanoporous sample surfaces were etched with different patterns. Preferential cell attachment was noticed on nanotube surface compare to almost no cells in etched Ti surface. Cell adhesion with vinculin adhesive protein showed higher intensity, positive contacts on nanoporous surface and thin focal contacts on the Ti-control. Immunochemistry study with alkaline phosphatase showed enhanced osteoblastic phenotype expressions in nanoporous surface. Osteoblast proliferation was significantly higher on anodized nanotube surface. Surface properties changed with the emergence of nanoscale morphology. Higher nanometer scale roughness, low contact angle and high surface energy in nanoporous surface enhanced the osteoblast-material interactions. Mineralization study was done under simulated body fluid (SBF) with ion concentration nearly equal to human blood plasma to understand biomimetic apatite deposition behavior. Although apatite layer formation was noticed on nanotube surface, but it was nonuniform even after 21 days in SBF.

Jan Marciniak

Papers

Electropolishing and passivation of NiTi shape memory alloy

Diamond-like carbon coatings for biomedical applications

Influence of the anodic oxidation on the physicochemical properties of the Ti6Al4V ELI alloy

Biomechanical analysis of stent–oesophagus system

Corrosion resistance of intramedullary nails used in elastic osteosynthesis of children