다중혈관 관상동맥 환자에서 y-문합을 이용하여 양쪽 내흉동맥만을 사용한 우회술의 조기 성적

Solar Engineering Of Thermal Processes

Solar photovoltaic (PV) energy has witnessed double-digit growth in the past decade. The penetration of PV systems as distributed generators in low-voltage grids has also seen significant attention. In addition, the need for higher overall grid efficiency and reliability has boosted the interest in the microgrid concept. High-efficiency PV-based microgrids require maximum power point tracking (MPPT) controllers to maximize the harvested energy due to the nonlinearity in PV module characteristics. Perturb and observe (PO second, no steady-state oscillations around the MPP; and lastly, no need for predefined system-dependent constants, hence provides a generic design core. A design example is presented by experimental implementation of the proposed technique. Practical results for the implemented setup at different irradiance levels are illustrated to validate the proposed technique.

High-Performance Adaptive Perturb and Observe MPPT Technique for Photovoltaic-Based Microgrids

It has become imperative for the power and energy engineers to look out for the renewable energy sources such as sun, wind, geothermal, ocean and biomass as sustainable, cost-effective and environment friendly alternatives for conventional energy sources. However, the non-availability of these renewable energy resources all the time throughout the year has led to research in the area of hybrid renewable energy systems. In the past few years, a lot of research has taken place in the design, optimization, operation and control of the renewable hybrid energy systems. It is indeed evident that this area is still emerging and vast in scope. The main aim of this paper is to review the research on the unit sizing, optimization, energy management and modeling of the hybrid renewable energy system components. Developments in research on modeling of hybrid energy resources (PV systems), backup energy systems (Fuel Cell, Battery, Ultra-capacitor, Diesel Generator), power conditioning units (MPPT converters, Buck/Boost converters, Battery chargers) and techniques for energy flow management have been discussed in detail. In this paper, an attempt has been made to present a comprehensive review of the research in this area in the past one decade.

Hybrid renewable energy systems for power generation in stand-alone applications: A review

A new fuzzy-logic controller for maximum power point tracking of photovoltaic (PV) systems is proposed. PV modeling is discussed. Conventional hill-climbing maximum power-point tracker structures and features are investigated. The new controller improves the hill-climbing search method by fuzzifying the rules of such techniques and eliminates their drawbacks. Fuzzy-logic-based hill climbing offers fast and accurate converging to the maximum operating point during steady-state and varying weather conditions compared to conventional hill climbing. Simulation and experimentation results are provided to demonstrate the validity of the proposed fuzzy-logic-based controller.

Fuzzy-Logic-Control Approach of a Modified Hill-Climbing Method for Maximum Power Point in Microgrid Standalone Photovoltaic System

This paper proposes a method of modeling and simulation of photovoltaic arrays. The main objective is to find the parameters of the nonlinear I-V equation by adjusting the curve at three points: open circuit, maximum power, and short circuit. Given these three points, which are provided by all commercial array data sheets, the method finds the best I-V equation for the single-diode photovoltaic (PV) model including the effect of the series and parallel resistances, and warranties that the maximum power of the model matches with the maximum power of the real array. With the parameters of the adjusted I-V equation, one can build a PV circuit model with any circuit simulator by using basic math blocks. The modeling method and the proposed circuit model are useful for power electronics designers who need a simple, fast, accurate, and easy-to-use modeling method for using in simulations of PV systems. In the first pages, the reader will find a tutorial on PV devices and will understand the parameters that compose the single-diode PV model. The modeling method is then introduced and presented in details. The model is validated with experimental data of commercial PV arrays.

Comprehensive Approach to Modeling and Simulation of Photovoltaic Arrays

This paper presents an easy and accurate method of modeling photovoltaic arrays. The method is used to obtain the parameters of the array model using information from the datasheet. The photovoltaic array model can be simulated with any circuit simulator. The equations of the model are presented in details and the model is validated with experimental data. Finally, simulation examples are presented. This paper is useful for power electronics designers and researchers who need an effective and straightforward way to model and simulate photovoltaic arrays.

Modeling and circuit-based simulation of photovoltaic arrays

This study deals with the regulation of the output voltage of photovoltaic (PV) arrays. As a case study, the DC-DC buck converter is used as an interface between the PV array and the load, but other types of converters can be used for the same purpose. The input voltage of the converter is controlled in order to regulate the operating point of the array. Besides reducing losses and stress because of the bandwidth-limited regulation of the converter duty cycle, controlling the converter input voltage reduces the settling time and avoids oscillation and overshoot, making easier the functioning of maximum power point tracking (MPPT) methods. The voltage regulation problem is addressed with a detailed analysis that starts with the modelling of the PV array and the converter. This analysis is followed by study, design, simulation and practical experiments of three closed-loop control strategies for the buck converter. Control stability and implementation considerations are presented.

Voltage regulation of photovoltaic arrays: small-signal analysis and control design

This paper shows that the performance of the perturb and observe (P&O) maximum power point tracking (MPPT) algorithm is improved when the electronic converter is correctly controlled. A linearized photovoltaic (PV) array model is used to obtain the transfer function of the electronic converter and to design a voltage compensator for the converter input voltage. A buck converter is used in this work.

Analysis and simulation of the P&O MPPT algorithm using a linearized PV array model

The control of the input voltage of DC-DC converters is frequently required in photovoltaic applications. In this spe cial situation, unlike conventional converters, the output vol tage is constant and the input voltage is controlled. This paper deals with the analysis and the control of the buck converter with constant output voltage and variable input.

http://www.scielo.br/pdf/ca/v19n4/a09v19n4.pdf

Marcelo Gradella Villalva

Papers

Comprehensive Approach to Modeling and Simulation of Photovoltaic Arrays

Modeling and circuit-based simulation of photovoltaic arrays

Voltage regulation of photovoltaic arrays: small-signal analysis and control design

Analysis and simulation of the P&O MPPT algorithm using a linearized PV array model

Dynamic analysis of the input-controlled buck converter fed by a photovoltaic array