Review of ultra-high performance concrete and its application in bridge engineering

The seismic response of a multi-span continuous bridge isolated with novel superelastic-friction base isolator (S-FBI) is investigated under near-field earthquakes. The isolation system consists of a flat steel-Teflon sliding bearing and a superelastic NiTi shape memory alloy (SMA) device. The key design parameters of an S-FBI system are the natural period of the isolated bridge, the yielding displacement of the SMA device, and the friction coefficient of the sliding bearings. The goal of this study is to obtain optimal values for each design parameter by performing sensitivity analysis of a bridge isolated by an S-FBI system. First, a three-span continuous bridge is modeled as two-degrees-of-freedom with the S-FBI system. A neuro-fuzzy model is used to capture rate- and temperature-dependent nonlinear behavior of the SMA device. Then, a set of nonlinear time history analyses of the isolated bridge is performed. The variation of the peak response quantities of interest is shown as a function of design parameters of the S-FBI system and the optimal values for each parameter are evaluated. Next, in order to assess the effectiveness of the S-FBI system, the response of the bridge isolated by the S-FBI system is compared with the response of the non-isolated bridge and the same bridge isolated by pure-friction (P-F) sliding isolation system. Finally, the influence of temperature variations on the performance of the S-FBI system is evaluated. The results show that the optimum design of a bridge with the S-FBI system can be achieved by a judicious specification of design parameters. Copyright © 2010 John Wiley & Sons, Ltd.

Optimal design of superelastic‐friction base isolators for seismic protection of highway bridges against near‐field earthquakes

This paper explores the effectiveness of shape memory alloy (SMA)/rubber-based isolation systems for seismic protection of bridges against near-field earthquakes by performing a sensitivity analysis. The isolation system considered in this study consists of a laminated rubber bearing, which provides lateral flexibility while supplying high vertical load-carrying capacity, and an auxiliary device made of multiple loops of SMA wires. The SMA device offers additional energy dissipating and re-centering capability. A three-span continuous bridge is modeled with the SMA/rubber-based (SRB) isolation system. Numerical simulations of the bridge are conducted for various near-field ground motions that are spectrally matched to a target design spectrum. The normalized forward transformation strength, forward transformation displacement and pre-strain level of the SMA device, ambient temperature and the lateral stiffness of the rubber bearings are selected as parameters of the sensitivity study. The variation of the seismic response of the bridge with the considered parameters is assessed. Also, the performance of the SRB isolation system with optimal design parameters is compared with an SMA-based sliding isolation system. The results indicate that the SRB isolation system can successfully reduce the seismic response of highway bridges; however, a smart isolation system that combines sliding bearings together with an SMA device is more efficient than the SRB isolation system.

https://iopscience.iop.org/article/10.1088/0964-1726/20/1/015003/pdf

Seismic assessment of bridge structures isolated by a shape memory alloy/rubber-based isolation system

Hysteretic behavior investigation of self-centering double-column rocking piers for seismic resilience

Performance of an innovative self-centering buckling restrained brace for mitigating seismic responses of bridge structures with double-column piers

Many highway bridges were severely damaged or completely collapsed during the 2008 Wenchuan earthquake. A field investigation was carried out in the strongly affected areas and over 320 bridges were examined. Damage to some representative highway bridges is briefly described and a preliminary analysis of the probable causes of the damage is presented in this paper. The most common damage included shear-flexural failure of the pier columns, expansion joint failure, shear key failure, and girder sliding in the transversal or longitudinal directions due to weak connections between girder and bearings. Lessons learned from this earthquake are described and recommendations related to the design of curved and skewed bridges, design of bearings and devices to prevent girder collapse, and ductility of bridge piers are presented. Suggestions for future seismic design and retrofitting techniques for bridges in moderate to severe earthquake areas are also proposed.

Qiang Han

Papers

Seismic damage of highway bridges during the 2008 Wenchuan earthquake