Journal ArticleDOI
Mechanical behaviour of ABS: An experimental study using FDM and injection moulding techniques
TLDR
In this paper, the effect of processing technique on the mechanical behaviour of virgin ABS was investigated in terms of varying raster angle and gap to further explore the potential of this technique.About:
This article is published in Journal of Manufacturing Processes.The article was published on 2016-01-01. It has received 407 citations till now. The article focuses on the topics: Injection moulding & Flexural strength.read more
Citations
More filters
Journal ArticleDOI
Mechanical and thermal properties of ABS/montmorillonite nanocomposites for fused deposition modeling 3D printing
TL;DR: In this article, an Acrylonitrile butadiene styrene (ABS) nanocomposites with organic modified montmorillonite (OMMT) were prepared by melt intercalation and evaluated by tensile, flexural, thermal expansion and dynamic mechanical tests.
Journal ArticleDOI
FDM-Based 3D Printing of Polymer and Associated Composite: A Review on Mechanical Properties, Defects and Treatments.
TL;DR: The most common defects on printed parts, in particular the void formation, surface roughness and poor bonding between fibre and matrix, are explored and an inclusive discussion on the effectiveness of chemical, laser, heat and ultrasound treatments to minimize these drawbacks is provided.
Journal ArticleDOI
A critical review on the fused deposition modeling of thermoplastic polymer composites
TL;DR: In this article, the challenges involved in the preparation of composite feedstock filaments and printing issues during the printing of nano composites, short and continuous fiber composites are discussed, and detailed explanation is given about the analytical and numerical models used for simulating the FDM printing process and for estimating the mechanical properties of the printed parts.
Journal ArticleDOI
The Influence of Manufacturing Parameters on the Mechanical Behaviour of PLA and ABS Pieces Manufactured by FDM: A Comparative Analysis
TL;DR: The bond between layers in PLA turns out to be extremely strong and is, therefore, highly suitable for use in additive technologies and is a reference of interest in studies involving the determination of mechanical properties of polymer materials manufactured using these technologies.
Journal ArticleDOI
Isotropic and anisotropic elasticity and yielding of 3D printed material
TL;DR: In this article, the effect of printing orientation on the elasticity and yielding properties of 3D printed materials is evaluated with experiments and a transversely isotropic and anisotropic elastic and yielding model is proposed.
References
More filters
Journal ArticleDOI
Anisotropic material properties of fused deposition modeling ABS
TL;DR: In this article, the properties of FDM parts fabricated by the FDM 1650 were analyzed using a Design of Experiment (DOE) approach, such as raster orientation, air gap, bead width, color and model temperature.
Journal ArticleDOI
Parametric appraisal of mechanical property of fused deposition modelling processed parts
TL;DR: In this paper, five important process parameters such as layer thickness, orientation, raster angle, Raster width and air gap are considered and their influence on three responses such as tensile, flexural and impact strength of test specimen is studied.
Journal ArticleDOI
A comparison of rapid prototyping technologies
Duc Truong Pham,Rosemary Gault +1 more
TL;DR: There are many different rapid prototyping (RP) technologies available as discussed by the authors, and a taxonomy is also suggested, along with a preliminary guide to process selection based on the end use of the prototype.
Journal ArticleDOI
Critical parameters influencing the quality of prototypes in fused deposition modelling
TL;DR: In this paper, the influence of process parameters on the quality characteristics of the prototypes using Taguchi technique has been assessed and the results of the study and the conclusions arrived from it.
Journal ArticleDOI
Improving dimensional accuracy of Fused Deposition Modelling processed part using grey Taguchi method
TL;DR: In this paper, the influence of important process parameters viz., layer thickness, part orientation, raster angle, air gap and raster width along with their interactions on dimensional accuracy of Fused Deposition Modelling (FDM) processed ABSP400 (acrylonitrile-butadine-styrene) part.