Fibers and Polymers 

About: Fibers and Polymers is an academic journal published by Springer Science+Business Media. The journal publishes majorly in the area(s): Fiber & Ultimate tensile strength. It has an ISSN identifier of 1229-9197. Over the lifetime, 4658 publications have been published receiving 57641 citations.

Nanocellulose reinforced PVA composite films: Effects of acid treatment and filler loading

Abstract: Nanocellulose was prepared by acid hydrolysis of microcrystalline cellulose (MCC) at different hydrobromic acid (HBr) concentrations. Polyvinyl alcohol (PVA) composite films were prepared by the reinforcement of nanocellulose into a PVA matrix at different filler loading levels and subsequent film casting. Chemical characterization of nanocelluloses was performed for the analysis of crystallinity (Xc), degree of polymerization (DP), and molecular weight (Mw). The mechanical and thermal properties of the nanocellulose reinforced PVA films were also measured for tensile strength and thermogravimetric analysis (TGA). The acid hydrolysis decreased steadily the DP and Mw of MCC. The crystallinity of MCC with 1.5 M and 2.5 M HBr showed a significant increase due to the degradation of amorphous domains in cellulose. Higher crystalline cellulose showed the higher thermal stability than MCC. From X-ray diffraction (XRD) analysis, nanocellulose samples showed the higher peak intensity than MCC cases. Reduction of MCC particle by acid hydrolysis was clearly observed from scanning electron microscope (SEM) images. The tensile and thermal properties of PVA composite films were significantly improved with the increase of the nanocellulose loading.

Application of silver nanoparticles to cotton fabric as an antibacterial textile finish

Abstract: A novel nano-silver colloidal solution was prepared in one step by mixing AgNO3 aqueous solution and an amino-terminated hyperbranched polymer (HBP-NH2) aqueous solution under vigorous stirring at room temperature. All results of Dynamic Light Scattering (DLS), Transmission Electron Microscopy (TEM) and UV/Visible Absorption Spectrophotometry indicated that silver nanoparticles had been formed in colloidal solution. Cotton fabric was treated with nano-silver colloid by an impregnation method to provide the cotton fabric with antibacterial properties. The whiteness, silver content, antibacterial activity and washing durability of the silver-treated fabrics were determined. The results indicated that the silver-treated cotton fabric showed 99.01 % bacterial reduction of Staphylococcus aureus and 99.26 % bacterial reduction of Escherichia coli while the silver content on cotton was about 88 mg/kg. The antimicrobial activity of the silver-treated cotton fabric was maintained at over 98.77 % reduction level even after being exposed to 20 consecutive home laundering conditions. In addition, the results of scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) confirmed that silver nanoparticles have been fixed and well dispersed on cotton fabrics’ surface and the major state of the silver presented on the surface was Ag0.

X-ray diffraction study of bamboo fibers treated with NaOH

Abstract: Bamboo fibers are a new kind of natural materials which have a big potential application in textile field due to some of their particular properties. However, high crystallinity and orientation structure can result in some undesirable properties and this will limit their further applications as textile materials. As a common used way, mercerization was adapted to treat bamboo fibers in this work in order to improve their undesirable properties. X-ray diffraction (XRD) was used to characterize their microstructure after treatment with NaOH. The amount of cellulose II and the crystallinity index based on the XRD results were calculated for the evaluation of the effectiveness of the different treatment conditions, such as alkali concentration, mercerization duration and temperature, as well as tension applied to the fibers during mercerization, on the transformation degree of cellulose I to cellulose II and decrystallization of the mercerized bamboo fibers. It has been found that each condition has different effects and that the greatest effectiveness of crystal lattice conversion and decrystallization could be achieved with such mercerization condition: 16 % alkali concentration, 10 minutes of mercerization at 20 °C without tension applied to the fibers.

Rheology of concentrated xanthan gum solutions: Steady shear flow behavior

Abstract: Using a strain-controlled rheometer, the steady shear flow properties of aqueous xanthan gum solutions of different concentrations were measured over a wide range of shear rates. In this article, both the shear rate and concentration dependencies of steady shear flow behavior are reported from the experimentally obtained data. The viscous behavior is quantitatively discussed using a well-known power law type flow equation with a special emphasis on its importance in industrial processing and actual usage. In addition, several inelastic-viscoplastic flow models including a yield stress parameter are employed to make a quantitative evaluation of the steady shear flow behavior, and then the applicability of these models is also examined in detail. Finally, the elastic nature is explained with a brief comment on its practical significance. Main results obtained from this study can be summarized as follows: (1) Concentrated xanthan gum solutions exhibit a finite magnitude of yield stress. This may come from the fact that a large number of hydrogen bonds in the helix structure result in a stable configuration that can show a resistance to flow. (2) Concentrated xanthan gum solutions show a marked non-Newtonian shear-thinning behavior which is well described by a power law flow equation and may be interpreted in terms of the conformational status of the polymer molecules under the influence of shear flow. This rheological feature enhances sensory qualities in food, pharmaceutical, and cosmetic products and guarantees a high degree of mixability, pumpability, and pourability during their processing and/or actual use. (3) The Herschel-Bulkley, Mizrahi-Berk, and Heinz-Casson models are all applicable and have equivalent ability to describe the steady shear flow behavior of concentrated xanthan gum solutions, whereas both the Bingham and Casson models do not give a good applicability. (4) Concentrated xanthan gum solutions exhibit a quite important elastic flow behavior which acts as a significant factor for many industrial applications such as food, pharmaceutical, and cosmetic manufacturing processes.

Coir fiber reinforced polypropylene composite panel for automotive interior applications

Abstract: In this study, physical, mechanical, and flammability properties of coconut fiber reinforced polypropylene (PP) composite panels were evaluated. Four levels of the coir fiber content (40, 50, 60, and 70 % based on the composition by weight) were mixed with the PP powder and a coupling agent, 3 wt % maleic anhydride grafted PP (MAPP) powder. The water resistance and the internal bond strength of the composites were negatively influenced by increasing coir fiber content. However, the flexural strength, the tensile strength, and the hardness of the composites improved with increasing the coir fiber content up to 60 wt %. The flame retardancy of the composites improved with increasing coir fiber content. The results suggest that an optimal composite panel formulation for automotive interior applications is a mixture of 60 wt % coir fiber, 37 wt % PP powder, and 3 wt % MAPP.